ProCurve 420 Información técnica Pagina 313
- Pagina / 363
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Line Reference
Wireless Interface Commands
preamble
This command sets the length of the signal preamble that is used at the start
of a data transmission.
Syntax
preamble [long | short-or-long]
• long - Sets the preamble to long.
• short-or-long - Sets the preamble according to the capability of
clients that are currently asscociated. Uses a short preamble if all
associated clients can support it, otherwise a long preamble is used.
Default Setting
Short-or-long
Command Mode
Interface Configuration (Wireless)
Command Usage
• Using a short preamble (96 microseconds) instead of a long preamble
(192 microseconds) can increase data throughput on the access point,
but requires that all clients can support a short preamble.
• Set the preamble to long to ensure the access point can support all
802.11b and 802.11g clients.
Example
HP420(if-wireless g)#preamble short-or-long
HP420(if-wireless g)#
transmit-limits
This command sets the reduction in transmit power required for an external
antenna to conform with local regulations.
Syntax
transmit-limits <low> <middle> <high>
low - The percentage of full power allowed for low radio channels.
(Options: 100, 90, 80, 70, 63, 56, 50, 45, 40, 35, 32, 28, 25, 22, 20, 18, 16,
14, 13, 11, 10)
8-107
- HP ProCurve 3
- Wireless Access Point 420 3
- Disclaimer 4
- Warranty 4
- Publication Number 4
- Applicable Products 4
- Trademark Credits 4
- 8 Command Line Reference 9
- A File Transfers 14
- Getting Started 15
- Introduction 16
- Conventions 16
- Command Prompts 17
- Screen Simulations 17
- Related Publications 18
- Sources for More Information 20
- Need Only a Quick Start? 20
- Advantages of Using the CLI 25
- Browser Interface 26
- Accessing the CLI 28
- Telnet Access 29
- Secure Shell Access 29
- Using the CLI 30
- Username: admin 31
- Password: 31
- Command Level Operation 32
- How To Move Between Levels 34
- ? symbol lists the 35
- Command Option Displays 37
- Configuration Modes 38
- CLI Control and Editing 42
- General Features 47
- The Home Page 49
- Support URL 50
- Web Browser Interface Logout 51
- Interface Session 52
- Setting SNMP Community Names 54
- SNMP] button 55
- Setting the Primary SSID 56
- Setting the Radio Channel 57
- Configuring TCP/IP Settings 58
- [Modify] button for the 60
- [Security Suite] button 60
- Status Reporting Features 62
- Station Status 65
- Event Log 67
- The Status Bar 68
- Neighbor AP Detection 68
- Settings] button 69
- 5. Click the 70
- button 70
- Passwords 77
- Figure 5-1. The User Window 79
- Modifying System Information 86
- CLI: Setting the System Name 87
- Configuring IP Settings 89
- Figure 5-5. The SNMP Window 95
- General System Configuration 102
- Configuring SNMP 102
- SNMP Trap] button 103
- Enabling System Logging 114
- [Event Log] button 115
- System Servers] button 115
- [Apply Changes] button 115
- Configuring SNTP 119
- CLI: Setting SNTP Parameters 121
- Parameters 123
- Accounting Servers] button 128
- Setting up Filter Control 132
- Filter Control] button 133
- CLI: Setting Traffic Filters 134
- Configuring VLAN Support 136
- Web: Enabling VLAN Support 137
- CLI: Enabling VLAN Support 139
- Contents 141
- Overview 142
- Setting the Country Code 143
- Port/Radio Settings] button 147
- [Radio Mode Change] button 147
- Configuring Radio Settings 150
- Modifying Antenna Settings 156
- Control Limits 158
- Add] button 163
- Wireless Security Overview 171
- Using the Security Wizard 179
- Configuring RADIUS Client 193
- Authentication 193
- Configuring MAC Address 199
- Command Line Reference 207
- General Commands 210
- HP420#reset board 213
- System Management Commands 215
- Default Setting 217
- 99 (no country set) 217
- HP420(config-mgmt)# 221
- System Logging Commands 234
- HP420(config)#logging clear 238
- HP420(config)# 238
- Example 239
- System Clock Commands 240
- SNMP Commands 245
- Command Mode 259
- Flash/File Commands 260
- HP420#bootfile hp420-2.bin 261
- HP420#delete test.cfg 263
- RADIUS Authentication 267
- HP420(if-wireless-g-ssid-1)# 270
- RADIUS Accounting 273
- 802.1X Authentication 278
- 802.1x session-timeout 280
- 802.1x supplicant user 280
- 802.1x supplicant 281
- MAC Address Authentication 284
- Filtering Commands 288
- Ethernet Interface Commands 292
- HP420(if-ethernet)# 293
- HP420(if-ethernet)#shutdown 296
- Wireless Interface Commands 299
- HP420(if-wireless-g)# 301
- HP420(if-wireless g)# 305
- Wireless Security Commands 321
- IAPP Command 335
- VLAN Commands 336
- File Transfers 341
- [Start Upgrade] button 355
- Index – 1 359
- 2 – Index 360
- Index – 3 361
- *5990-6006* 363
Relacionado con productos y manuales para Software ProCurve 420
Software ProCurve 2610-PWR Información técnica
(469 paginas)
(469 paginas)
Software ProCurve 2610-PWR Información técnica
(364 paginas)
(364 paginas)
Software ProCurve 2510G Series Información técnica
(412 paginas)
(412 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales